3D printed robotics parts in Dhaka
Updated
We print robot parts in PLA for university and college students, robotics clubs and anyone building a machine for a competition or a lab project: chassis plates, motor brackets, grippers, wheel hubs and sensor mounts.
What teams usually bring
- Chassis base plates and top decks for line followers, sumo bots and soccer bots
- Brackets for TT gear motors, N20 motors and SG90 or MG996R servos
- Gripper fingers, claw linkages and small arm segments
- Mounts for HC-SR04 ultrasonic sensors, IR arrays, cameras and battery holders
- Spacers, standoffs and cable clips
What to send
The best input is the file your team already designed. Export STL or 3MF from Fusion, SolidWorks or Onshape, put it in a Google Drive folder and paste the link; a STEP file works too. For an open design, a MakerWorld, Printables or Thingiverse link is enough. Without a model, describe the part, its main dimensions and the motor or sensor it has to fit, and we will try to find or adapt something close to it. We do not design whole robots from scratch.
Holes, screws and fit
Printed holes come out slightly smaller than drawn, so a hole modelled at exactly 3.0 mm is often tight on an M3 bolt. Model M3 clearance holes at around 3.2–3.4 mm and M4 at around 4.3–4.5 mm, or plan to run a drill bit through them. Where parts slide or press together, leave about 0.2–0.3 mm of clearance. We do not fit heat-set inserts, so design for bolts and nuts: a hexagonal pocket for an M3 nut works well in PLA.
Where PLA works on a robot, and where it does not
PLA is stiff and accurate, which suits chassis plates, brackets and mounts on small and medium robots. It is less forgiving under sharp impact than PETG or nylon, so a sumo wedge or a combat robot's armour may crack where a tougher plastic would bend. It softens around 55–60°C: keep it off motor casings that run hot, voltage regulators and anything you solder near. Do not use it for a part that carries a person's weight or anything safety-critical.
Big chassis, colour and finish
A chassis too big to print in one go is split into parts that bolt or glue together; tell us where a joint must not go. Parts come in black or white. For competition parts "as printed" is usually right: sanding adds cost, not strength. "Sanded and painted" is worth it for a robot going on show at an exhibition.
What decides the price
Every job is priced by hand from the file, from ৳99. For robot parts the price mostly follows the plastic and machine hours in the heaviest pieces, such as solid chassis plates, and the number of copies. Thin, ribbed parts cost less than solid blocks of the same size.
Send the files, the quantity and your deadline through the request form at krezit.cc/request. We reply with a price on WhatsApp or email, usually the same day, and printing takes 2–3 days after you confirm.
Questions
- Can I get robot parts 3D printed in Dhaka before a competition?
- Yes. Krezit replies with a price usually the same day, and printing takes 2–3 days once you confirm. Courier time then depends on where you are, so send the files as early as you can before the event.
- Is PLA strong enough for a robot chassis?
- For line followers, soccer bots and most lab robots, yes: PLA is stiff and holds bolts well. It is more brittle under hard impact than PETG or nylon and softens around 55–60°C, so avoid it for combat armour or parts touching hot motors.
- Can you print a mount that fits an MG996R servo or an N20 motor?
- If you send a model made for that servo or motor, we print it as designed. If you only have the part number, describe what you need and we will try to find or adapt an existing mount close to it.
- Do you add threaded inserts to printed parts?
- No. Design the part for bolts and nuts instead, with M3 or M4 holes slightly larger than the bolt and a hexagonal pocket to hold the nut.
