3D printed electronics enclosures in Dhaka
Updated
We print cases and enclosures for electronics projects: boxes for an Arduino, ESP32 or Raspberry Pi, housings for a custom PCB, and front panels for sensors and displays. Most of them are for students finishing a thesis or final-year project and for people building IoT devices.
Typical enclosures
- Raspberry Pi cases with openings for the ports and room for a small fan
- Arduino Uno or Nano boxes with a cut-out for the USB cable
- ESP32 and ESP8266 housings for weather stations, smart switches and sensor nodes
- Project boxes with a window for an OLED or 16x2 LCD and holes for push buttons
- Two-part enclosures for a custom PCB, with standoffs that match its mounting holes
Start from an existing case if you can
Popular boards have hundreds of ready-made case designs on MakerWorld, Printables and Thingiverse, and a link to one is the quickest way to order. If you designed your own, send STL, 3MF or STEP files through a Google Drive link. If you only have the board, tell us its name, the PCB size and where the connectors sit, and we will try to find or adapt a case close to it.
Measure before you model
Enclosures fail on small things: a USB port a millimetre out, a lid that will not close over a tall capacitor. Measure the real board with callipers, not just the datasheet, and check the height of the tallest component. Leave about 0.2–0.3 mm around the board and around any lid that slides or snaps into place. Model standoff holes for M2.5 or M3 screws, or leave room for a nut below, as we do not fit heat-set inserts. A screwed lid survives repeated opening better than a snap-fit.
Heat inside a PLA box
PLA softens around 55–60°C, which matters more in a closed box than people expect. A Raspberry Pi under load, a linear regulator or a motor driver can push the air inside well above room temperature, and a Dhaka summer starts warm. Add vents, keep hot components off the walls, and do not use a PLA case for anything that runs hot by design, such as a power supply or a battery charger. PLA is not a flame-retardant plastic, so it should not be the only protection around mains wiring.
Colour and finish for the presentation
Black hides dust and fingerprints; white lets an LED glow through a thin wall, which some projects use as a status light. "As printed" is fine for a working build. For a thesis defence or project show, "sanded" takes the layer lines off, and "sanded and painted" gives the cleanest box.
What decides the price
Every case is quoted by hand from the file, from ৳99. A small ESP32 box uses little plastic and prints quickly; a large enclosure with thick walls, or one that needs supports under overhangs, costs more, and sanding or painting adds hands-on time.
Send the model link or your files, with the board name, at krezit.cc/request. You get a reference like REQ-XXXXX-XXXXX to follow the job at krezit.cc/track.
Questions
- Where can I get a Raspberry Pi or Arduino case printed in Dhaka?
- Krezit prints enclosures to order in Dhaka and sends them by courier anywhere in Bangladesh. Send a model link or your file at krezit.cc/request and we reply with a price, usually the same day.
- Can you make a case for my custom PCB?
- If you have a model of the case, yes. If not, send the board size, hole positions and connector locations, and we will try to find or adapt an existing enclosure close to it; we do not design one from scratch.
- Will a PLA case melt with electronics inside?
- Not with most low-power boards, but PLA softens around 55–60°C. Add vents, keep regulators and drivers away from the walls, and do not use PLA for power supplies or anything that runs hot.
- How long does an enclosure take for a thesis deadline?
- Printing takes 2–3 days after you confirm the quote, then courier delivery. Allow for that before your submission date, and add a few days if you may want a second version.
